Home
Categories
Send inquiry
Home
About Us
Products
Chemical
Dacromet Coating
Zinc Flake Coating
Silicon Slice Detergent
Diamond Wire Cutting Fluid
Equipment
Coating Equipments
Curing Furnace
Other Equipments
Fastener
Standard Fastener
Auto Fastener
News
FAQs
Contact Us
Home
About Us
Products
Chemical
Dacromet Coating
Zinc Flake Coating
Silicon Slice Detergent
Diamond Wire Cutting Fluid
Equipment
Coating Equipments
Curing Furnace
Other Equipments
Fastener
Standard Fastener
Auto Fastener
News
FAQs
Contact Us
Featured
Home
News
News
Automobile aluminum wheel hub system solutions
Posted on 2016-04-12 1、Cutting fluid products:JH-MCF – 211 Microemulsion extreme pressure cutting fluid1, Cutting fluid products Product synopsis: this product is a micro emulsified cutting fluid, extreme pressure of lubricating oil, extreme pressure and anti-wear agent, anti-r...
Read More
Automobile brake system solutions
Posted on 2016-04-15 1, Cutting fluid products JH-MCF – 201 General type microemulsion cutting fluidProduct synopsis: this product is a universal micro emulsive cutting fluid, by the lubricating oil, antiwear agent, anti-rust agent and other additives. Suitable for machining cast i...
Read More
Junhe teach you how to prevent water zinc flake coating hexavalent chromium carbide
Posted on 2016-06-01 Because Water Base Zinc Flake Coating is easy to moisture absorption, especially in the rainy season. Construction or Shanghai juji good workpiece is prone to some problems, such as the zinc flake coating antirust mainly by the hexavalent chromium coating repair ag...
Read More
zinc flake coating process
Posted on 2016-06-22 Zinc flake coating Is a new type of the corrosion resistance coating,it has been widely used,zinc flake coating process mainly is the base material,degreasing, derusting, coating, preheating, curing, cooling.1. Degreasing: workpiece surface must be degreased,generally has...
Read More
Junhe zinc flake coating advantage
Posted on 2016-06-22 Junhe zinc flake coating paint is made of high quality raw materials,is anti-corrosion proucts instead of zinc plating, hot galvanizing. Have a series of products, which can meet the requirements of customers processing on different levels.Cost-effective: Junhe zinc flake...
Read More
FASTENER EXPO SHANGHAI 2016
Posted on 2016-06-26 On Jun .25,1016,Asia’slargest and world famous fastener exhibition, the 2016 Fastener Expo Shanghai sucessfully concluded at the Shanghai World Expo Exhibition & Convention Center . The Expo is jointly organized by ITE Asia Exhibitions Limited and Shanghai ITE E...
Read More
Zinc flake coating line improvement
Posted on 2016-06-29 Zinc flake coating line improvementJunhe DST S800 + zinc flake coating line made improvement on the following points:First.Coating machine1. Optional isolation room2. The feeding door is made by No.4 square tube,rigid and stable,elegant appearance.3. The cylinder protecti...
Read More
Junhe Stock: Dacromet industry, Evergreen
Posted on 2016-07-07 Looking at the domestic market Dacromet, the initial formation of the Yangtze River Delta, Pearl River Delta and Bohai Bay three fastener industry gathering area. China Surface Engineering Association of special coating professional committee established in 2003.Changzhou...
Read More
Cause analysis and treatment of effusion in dacromet production
Posted on 2016-07-21 Phenomenon: paint effusion in the teeth of the products, screw and hole.Reason:1. Viscosity high, temperature of the products high.2. Centrifugal speed low, time less and short.3. Too much extra paint on the basket.4. Degreasing in pre-treatment process is not clean, has ...
Read More
Several typical technical solution of JUNHE’s dacromet coating
Posted on 2016-07-28 1.Dip spin coating This is the most widely applied measure for coating fasteners and stamping parts of bolts, nuts, springs, screws. First, put the workpiece which after pre-treatment in the basket, dip coating, remove extra paint by centrifugal spinning, and then cu...
Read More
<<
< Previous
1
2
3
4
5
6
Next >
>>
Page 3 / 14